Avia Sport, in association with PRISM Inc., has developed A.P.A. edge connectors manufactured from an extremely durable soft plastic that can withstand extreme temperature changes. There are 13 sizes available. Use with pultruded carbon tubes and rods, wrapped spars, some filament wound epoxy tubing, as well as fiberglass rods.

The "T" in TAPA stands for "Tiny" and these are the smaller leading edge connectors popular with some of the skinnier wrapped or pultruded carbon tubes on very light kites.

<more about this item>

Tradewinds Angled Edge Connectors are the connector of choice for Dual line kites by FLEXIFOIL / COBRA KITES, and other European Kite designers. Angled Leading Edge connectors secure the kite frame by keeping spreaders from popping away from the sail. Tradewinds Angled Edge Connectors are made from a durable hard plastic that does not distort under stress. Three sizes available.

<more about this item>

Dihedrals are molded connecters that pre-form a dihedral or keel in your Eddy or Diamond kite. Assemble your kite by inserting the spreaders into the angled channels, then insert the spine through the center hole on the dihedral We have them in smaller sizes for Eddy trains or in larger sizes for Diamonds or whatever needs a dihedral. Dihedrals are available in 4 different inside diameters for different rod sizes. Each is pre-molded to the proper angle to form a dihedral for small to medium sized kites. The hole for the spine is slightly smaller than the hole for the spreaders in most cases. You could easily drill this out.

<more about this item>

Excel Dihedrals are made with precision tooling in Europe. Molded with accurate sizing, these are the cleanest dihedrals we have found. Available in a variety of sizes and very durable. Each is pre-molded to the proper angle to form a dihedral for small to large sized kites.

<more about this item>

Angled Edge Connectors are polyurethane molded to fit a wide range of carbon rods and tubes. They are economical, light weight, and provide a clean look for your kite or other structure. Some of these connecters are available with different sized spreader and Leading Edge fitting, which is useful for tapered carbon fiber tubes.

We've been unable to obtain resupply of item #225104, the 3.1mm angled edge connectors. As alternatives, consider:

Item #021001-a HQ flexible rubber 3mm straight edge connector that you may find will bend sufficiently to serve as a substitue, or

Item #021004-HQ's somewhat shorter molded rubber angled edge connector, or

Item #020521-the APA molded angled edge connector, or

Item #020801-the FSD molded straight edge connector-for micro applications-this somewhat flexible connector may bend to suit your requirements.

<more about this item>

FSD Edge Connectors are ideal for using on small solid carbon and fiberglass rod or pultruded carbon fiber tubing. They have unique flanges to keep the bridle harness from slipping off the connector. Available in four sizes. Made from a semi hard material that is not too pliable.

<more about this item>

Vinyl End Caps (VEC) are best known for protecting the ends of your spars, end caps also save wear and tear on your sail fabric from spar abrasion. Vinyl End Caps can be used to slip over wing tip nocks for protection and to prevent the flying line from getting snagged. There are so many sizes to choose from you can find a multitude of uses for them. Try for a snug fit so that you won’t have to glue them on. Do this by choosing a size slightly smaller than the diameter of your spar. For example, if you have .240” carbon rod you would choose the VEC.234”.

Our VEC's are listed from smallest to largest diameter. All lengths are 1/2" unless noted.

<more about this item>

These ferrules fit carbon tubes in sizes .110" through .240". Sizes .180 and .210 of these external ferrules can also be used as internal ferrules for Avia Sport EXCEL wrapped carbon tubes.

Aluminum ferrules are a lightweight method of fitting two short carbon rods or carbon tubes together and creating a longer spar. This is great if you want to fold down your kite to fit in your car, for example.

<more about this item>

External Brass Ferrules are made to accommodate smaller sizes of fiberglass and carbon rods. These micro ferrules are good for connecting two lengths of rod or making a kite more compactable. They can be crimped or bent into a dihedral. Available in assorted micro sizes and lightweight.

<more about this item>

External Metal Ferrules are used to connect hardwood dowels and solid and tubular fiberglass rods to make a longer spar or to make a kite more compactable. They are constructed of either aluminum (EAF) or steel (ESF). Metal ferrules can be dimpled and in most cases bent to create preformed dihedrals for Eddy style kites.

<more about this item>

External fiberglass ferrules are cut from standard filament wound epoxy tubes. They are used to join two lengths of hardwood dowels, fiberglass rods and tubes, and carbon fiber rods and tubes together to form longer spars for kites, tents, and more. All ferrules are named after the fiberglass tubes from which they are cut.

<more about this item>

Internal fiberglass ferrules are either solid (IFS) or thick hollow tubes (IFH) and are inserted inside the ends of two tubes to connect them together. Internal ferrules make a smoother connection that does not have the bulk of an external ferrule. They fit those hard to fit tubes where nothing else is available.

<more about this item>

These extra long fiberglass ferrules are cut from pultruded wound tubes. They are used for large framework structures that require added support and strength. Use as a ferrule or to reinforce lengths of fiberglass rod. These ferrules are named by the outside diameter of the tubing from which they are cut. FGH stands for FiberGlass Hollow and they are a thick-walled tube built for strength.

<more about this item>

Internal Carbon Ferrules are light weight and very rigid. They are available in two sizes. These ferrules are perfect size for the SkyShark non-tapered and G-Force Skinny tapered spars.

<more about this item>

Line Tensioners make your bowline tension easier to adjust. Bowlines are tension lines commonly used on Rokkaku Kites, Eddie Kites, and Edo kites to form a curve in a flat sail, arcing from side to side. By doing this, the kite becomes stable and flies in lighter wind. Use the flat tensioner for regular sized kites and the bent one for heavy duty applications.

<more about this item>

Avia Sport kite nocks are designed with rounded tips. The rounded tip prevents the kite nock from getting stuck in the ground when the kite lands on the wing tip. Avia nocks are not as susceptible to warping or breaking like sharp-ended nocks, plus they‘re safer. Avia nocks are a perfect match for Goodwinds carbon fiber tubes. Lightweight plastic caps are available in all sizes from .1960" to .2540".

<more about this item>

Arrow Nocks are the old school version that were used on classic stunt kites such as the Hawaiian 16, North Shore Extreme, California Wasp, Chicago Bee, and many others. Arrow Nocks are glued on to Nock Inserts when utilized for fiberglass tubing. When used with wood dowels, simply taper the end of dowel with pencil sharpener and insert dowel into the Arrow Nock. Fix in place with electricians tape or glue. Available in four sizes.

<more about this item>

Nock Inserts are small aluminum fittings that fit inside Fiberglass Tubing, ProSpars, and SkyShark non-tapered spars. The proper size nock fits over the pointed end of the insert and is glued or taped in place. Please see the Arrow Nock table for nock sizing.

<more about this item>

Converta Sleeve Inserts are sized to fit inside Fiberglass Tubing, ProSpars, SkyShark non-tapered spars, Avia G-Force and Excel spars. They are used to prevent the hollow ends of the tubes from crushing. Available in one size; be sure to check your inside diameter before ordering.

We are starting to run low on these items and they probably will not be replaced unless there's a hew & cry.

<more about this item>

FSD End Caps serve as nocks for micro to medium sized rods. They are precision molded hard plastic with a unique design that prevents flying line from snagging on them. Made in Europe, FSD End Caps are extremely durable and available in a variety of sizes.

<more about this item>

HQ Split Nocks are precision made in Germany and are available in a wide range of sizes. HQ Split Nocks are extremely durable and clean looking. Give your kite the high quality touch it deserves with Excel Split Nocks.

Note: The 8mm is no longer available although we have a few left in stock.

<more about this item>

Rounded Nylon Nocks are similar to the Avia rounded nock and little bit more economical. Molded out of a durable nylon material and available in two sizes. The 3.2mm is the same nock used on the 3.1mm rods of the Beetle Dual Line Stunt Kite made by Flying Wings.

<more about this item>

Metal Rings and Triangles are useful for numerous applications. Use on multiple bridle kites such as Parafoil, Flare, and Rokkaku Kites to join the bridles at a single point, where the flying line will be attached. Use for joining the bridle lines on a windsock for hanging. Use the Split Rings for attaching tails through a grommet or loop on a kite. The Split Rings are made from nickel-plated tempered steel. The closed rings are made from aluminum.

<more about this item>

O-rings can be used in place of shock cord for a cleaner look and tighter fit on your standoff or leading edge. Our U.V. resistant O-rings don’t break or deteriorate due to sun exposure. Simply push the O-ring part way through the sail tensioning loop, pull the ring through itself, and stretch the pulled end over the nock. O-rings can also be used to hold two intersecting spars together, such as a top spreader intersecting the spine on a stunt kite. Available in one size.

<more about this item>

Clip-On Stoppers are ideal when you want to hold leading edge and T-connectors in place on your carbon fiber or fiberglass spreader or standoff. When you want a clean and professional look, use clip on stoppers. To permanently fix Clip on stoppers in place, put a drop of Zap-a-Gap or Superglue on the inner surface of stopper. Clip on Stoppers are molded from a durable hard plastic and come in a variety of sizes to fit almost any rod.

<more about this item>

Brass Snap Swivels are perfect for small single line kites or for windsocks. We stock three popular sizes. Available in 10, 30, and 50 pound test strength sizes.

<more about this item>

Rosco Stainless Steel Coastlock Swivel Snaps are easy to use and heavy duty. They're available in 4 convenient sizes.

<more about this item>

This scissor action, plated brass snap opens with slight finger pressure and can be used on your kite, windsock, or wherever else you need a stong snap. Holds where others fail. 2 sizes available.

<more about this item>

Converter Ferrules, sometimes called PINS or PINGS (for "Plug-in Skinny" and "Plug-in G-Force"), are ideal for connecting two spars with different diameters together. Their most common use is for connecting wrapped tapered spars to straight pultruded spars. They can also be used as internal or external plugs that protect the end of carbon spars from being crushed. Precision made out of a hard durable nylon, Converter Ferrules are available in 5 sizes.

<more about this item>

INVENTO/HQ is supplying the Kite Market with precision molded Edge Connectors in sizes of 4.0mm, 5.0mm, 5.5mm, 5.9mm and 6.3.

<more about this item>

INVENTO/HQ Straight Edge Connectors are precision molded and very durable.

<more about this item>

Heat Shrink Tubing has a multitude of uses. Enclose a metal ferrule with heat shrink for a streamlined appearance or strengthen a fiberglass ferrule. Add extra dimension to thin standoffs. Shim a spar that’s too small for a fitting. Remember that it shrinks to ˝ its original size so select the size according to the job. The Heat Shrink Tubing we offer has an inner adhesive that eliminates the need for gluing if used as a stopper.

<more about this item>

Apex Nocks are one piece nocks sized to fit over the outside of most pultruded carbon spars. They are durable, light weight and easy to use. The .2650 size also fits the fiberglass A-20 spar.

<more about this item>

Lightweight Aluminum Ferrules are designed in a lightweight aircraft aluminum alloy specifically as external ferrlues for wrapped and pultruded carbon rods. These ferrules have a very thin wall so they are feather light. Lightweight Ferrules are on closeout so get them while they last!

<more about this item>

Goodwinds Aluminum Ferrules are manufactured to fit carbon rods with a close tolerance. Our aluminum ferrules are machined to custom fit even the smallest size of pultruded carbon shafts. This custom fit reduces shaft breakage due to lateral stress and decreases ferrule failure with the proper wall thickness. Our ferrules are manufactured from durable extruded aluminum. Each ferrule has a dimple in the middle to prevent the spar from sliding all the way through. These ferrules normally sell for $0.75 apiece, but are being discontinued so they are priced to move.

<more about this item>

Kerschwing Edge Connectors are made from pre-molded Polyamid material that contains graphite. The craftsmanship and design of this connector is superb. Precision molded heavy-duty edge connectors. This edge connector has a unique bridle holder to keep it from sliding off. Both leading edge and spreader holes are the same size. Four sizes are available.

These connectors are on closeout so get some while they last!

<more about this item>

Vinyl Tubing is considered old school but it is an extremely versatile material. It is the least expensive source for customized fittings. It is available in a broad range of inside and outside diameters. Vinyl Tubing is on closeout so pick some up while it lasts!

<more about this item>

Tapered End Plugs (TEP), work well in place of Vinyl End Caps when you need to fit a spar through a tight channel or pocket. TEP also provide tubular spars with a little extra reinforcement to prevent spar ends from crushing. Available in 3 sizes.

<more about this item>

Goodwinds Soft Nock is a molded connector that can be used as a substitute for arrow nocks for entry level sport kites. They are heftier than most one piece nocks and will withstand all the wear and tear of a beginner’s ground pass attempts. To speed production, these connectors slip onto the leading edge and spine ends without any need for gluing. Fits pultruded carbon spars sized .230” through .254” as well as fiberglass A-20 spars. We are closing out these connectors so they’re priced to move.

<more about this item>

Ball bearing stainless steel swivel clips are precision made and spin smoothly with very little friction, like butta. These cost a bit more but hey, they're stainless, possessed of a secure snap and balls that are the cat's meow for smooth action and minimal twisting.

<more about this item>

The Exel T Connectors, or Cross Connectors, are molded plastic made by HQ Kites & Designs. They are designed for use as a lower spreader connection at the spine on Dual Line Stunt Kites. There is an internal wall of the T piece that prevents the spreader from sliding all the way through the channel. They are very durable and come in several sizes.

<more about this item>

Rosco stainless steel coastlock snaps can work with your choice of swivels or directly on your line or other product.

<more about this item>

These Premier Center T connectors are made from injection molded plastic and are very strong. They're great when you want a T-Connector without much bulk.

<more about this item>

JACO Standoff Spreaders connect the spreader rod to the standoff. These standoff spreaders are created for a .230" outer diameter spreader and a .118 standoff.

<more about this item>

APA Standoff Connectors attach to the lower spreader through the large hole. The standoff spar opening is a standard .210" (could fit .220 tightly). APA Standoff Connectors are made from a durable, medium soft material and are very pliable. APA Standoff Connectors also work well as right-angled connectors for framing various styles of Box Kites. Four sizes are available.

<more about this item>

Stand Off Connector by Flying Wings are the economical version of the APA Standoff connectors. The plastic material they are molded from is a little harder than the APA’s but they work just as good. Available in three popular sizes.

<more about this item>

Goodwinds Spreader side Standoff Connector is an economical choice for connecting standoffs to spreaders. Available in two sizes. These connectors are on closeout and priced to move.

<more about this item>

Tradewinds Spar Grabber Standoff Connectors fit on to the spar side of the standoff. When used with the Tradewinds Sail Grabber, you simply insert the sail side of standoff into reinforced hole at the trailing edge of kite sail, and clip the Tradewinds Spar Grabber on to the lower spreader of your kite. Available in two popular standoff sizes, and a wide range of popular spreader sizes. Tradewinds Spar Grabber Standoff Connectors also work well as right-angled connectors for framing various styles of Box Kites.

<more about this item>

Use HQ Flat Fold Over Standoff Sail Connectors to attach other end of standoff to kite sail by snapping plug through reinforced hole on sail. Unlike the other sail connectors, you can attach and remove these connectors from the sail without having to remove the standoff spar. Made of lightweight durable plastic, these are very sleek on the backside and won’t snag your fly lines. Comes in two popular sizes.

"Flat" refers to the flat, somewhat rounded nature of the insertible tip. See also HQ's non-flat, or pointed, sail connector in this section.

<more about this item>

HQ Fold Over Standoff Sail Connectors attach the sail end of standoff to kite sail by snapping plug through reinforced hole on sail. Unlike the other sail connectors, you can attach and remove these connectors from the sail without having to remove the standoff spar. Comes in two popular sizes. Made of durable plastic, these are easy to use.

"Pointed" refers to the nature of the insertible tip. See also HQ's flat sail connector in this section.

<more about this item>

JACO Standoff Sail Connector System is a light weight sail connection for standoffs. It incorperates a rubber “O” ring to sucure fitting at the sail side of connection. Use the JACO standoff connector by inserting plug through reinforced hole on kite sail. The “O” ring fits over the plug to secure the connector to sail. Comes in two popular sizes.

<more about this item>

Tradewinds Sail Grabber Standoff Connectors are lightweight and economical. Tradewinds Sailgrabbers fit into a small reinforced hole at the trailing edge of your kite sail. They are similar to the JACO Standoff System but without the “O” ring. There is only one size left, and when they're gone, they're gone - the company that made these is now out of business.

<more about this item>